- ঝর্ণা অগ্রভাগ, হালকা ও পাম্প
- ঝর্ণা নিয়ন্ত্রণ এবং সফ্টওয়্যার
- ঝর্ণা নকশা
- বাদ্যযন্ত্রের নৃত্যের ঝর্ণা
- ওয়াটার স্ক্রিন প্রোজেকশন লেজার শো
- জল ফায়ার ফোয়ারা
- গ্রাফিকাল জলপ্রপাত | ডিজিটাল জলের কার্টেন
- লামিনার ফোয়ারা | জাম্পিং ঝর্ণা
- ডিজিটাল সুইং ঝর্ণা
- কৃত্রিম কুয়াশা ঝর্ণা
- শুকনো ফ্লোর ফোয়ারা
- ইন্টারেক্টিভ ফোয়ারা
সঙ্গীত ফোয়ারা নিয়ন্ত্রণ মন্ত্রিপরিষদের অপারেশন গাইড
আমাদের সাথে যোগাযোগ করুন
Fountain Control Cabinet User Manual
I. Conditions of Using Control Cabinet：
The control center of a fountain is the electrical control cabinet, how to operate a fountain is
mainly about operating the control cabinet. The conditions of use are as below:
1. Good ventilation, no corrosion and flammable gas.
2. The highest temperature not to exceed 45 ℃, the lowest temperature is not lower than 5 ℃.
3. The relative humidity of the air is not more than 90%.
4. Voltage range AC 380V±5％，50HZ
II. Description Of The Knobs On Control Panel
1. Power Switch：
Only when the main power switch of each control cabinet is closed can the operation switch on the panel come into effect.
2. Automatic/Manual Switch：
When the switch is on AUTOMATIC, the fountain show can be controlled by computer.
When the switch is on MANUAL, it’s mainly used for single water shape, all the water shape switches on the panel can act independently, being used for water shape debugging, users can also combine different water types according to their preferences. If it's a programmed fountain, when the switch is on the position of AUTOMATIC, the fountain will perform as programmed.
3. Lamp Switch：
Users can turn off the colored lights according to their needs during the day.
III. Operating Steps：
All the fountain control cabinets have a main circuit breaker,which can cut off the main power supply of the control cabinet, so as to facilitate maintenance and repair.
This control cabinet operates in two ways: manual operation/automatic operation.
1. Preparation before operating：Check whether the control knobs on the control panel in the control cabinet are in the stop state，Then close the main power circuit breaker in the control cabinet and check whether the voltmeter display of each control cabinet is normal.
2. Manual operation：Place the Automatic/Manual knob on the position of Manual, then choose relative knobs on panel to perform corresponding water types.
3. Automatic Operation：Place the Automatic /Manual knob on the position of Automatic, the fountain show will be performed automatically.
4. The RGB light switch on the control panel can be opened at night.
5. Close the reverse operation.
In order to make the equipment always in the best condition, daily maintenance and regular maintenance should be carried out.
1.Dust the electric cabinet once a month.
2. The exhaust fan of the equipment shall be checked semiannually.
3. Water quality should be kept clean in the fountain pool, and rubbish are prohibited to be thrown into the pool, so as to prevent water pump and sprinkler head from being blocked and equipment from being damaged.
4. The fountain pool shall be cleaned irregularly, and the pipes and pumps shall be painted again if necessary.
1. The control room shall be equipped with safety and fire fighting facilities suitable for electrical safety requirements.
2. When the fountain is in operation, operators are strictly prohibited to leave the control room, must inspect the operation of various electrical control equipment at any time. If any abnormality is found, the power should be cut off immediately and the fountain should be stopped to avoid the expansion of the accident.
3. When maintaining the control system, the main power should be cut off. People without qualification is strictly prohibited to operate and maintain the control equipment system.
4. Do not pile up other sundries in the control room. It is strictly prohibited to connect other electric wires on the control cabinet.